DESIGN OF CONCRETE STRUCTURES -I syllabus with notes free download mdu btech - Printable Version +- studentsuvidha (https://studentsuvidha.com/forum) +-- Forum: Engineering zone (https://studentsuvidha.com/forum/Forum-Engineering-zone) +--- Forum: Mdu B.Tech papers and Notes- free download (https://studentsuvidha.com/forum/Forum-Mdu-B-Tech-papers-and-Notes-free-download) +---- Forum: CIVIL department Mdu btech papers and Notes -free downloads (https://studentsuvidha.com/forum/Forum-CIVIL-department-Mdu-btech-papers-and-Notes-free-downloads) +----- Forum: 4rth semester civil mdu btech papers and Notes (https://studentsuvidha.com/forum/Forum-4rth-semester-civil-mdu-btech-papers-and-Notes) +----- Thread: DESIGN OF CONCRETE STRUCTURES -I syllabus with notes free download mdu btech (/Thread-DESIGN-OF-CONCRETE-STRUCTURES-I-syllabus-with-notes-free-download-mdu-btech) |
DESIGN OF CONCRETE STRUCTURES -I syllabus with notes free download mdu btech - rkrusty - 12-29-2014 DOWNLOAD PAPERS HERE
DOWNLOAD NOTES HERE SECTION-A Unit-I: Elementary treatment of concrete technology: Physical requirements of cement, aggregate, admixture and reinforcement, Strength and durability, shrinkage and creep. Design of concrete mixes, Acceptability criterion, I.S. Specifications. Unit-II: Design Philosophies in Reinforced Concrete: Working stress and limit state methods, Limit state v/s working stress method, Building code, Normal distribution curve, characteristic strength and characteristics loads, design values, Partial safety factors and factored loads, stress -strain relationship for concrete and steel. SECTION-B Unit-III: Working Stress Method: Basic assumptions, permissible stresses in concrete and steel, design of singly and doubly reinforced rectangular and flanged beams in flexure, steel beam theory, inverted flanged beams, design examples. Unit-IV: Limit State Method: Basic assumptions, Analysis and design of singly and doubly reinforced rectangular flanged beams, minimum and maximum reinforcement requirement, design ex amples. Unit-V: Analysis and Design of Sections in shear, bond and torsion -Diagonal tension, shear reinforcement, development length, Anchorage and flexural bond, Torsional, stiffness, equivalent shear, Torsional reinforcement, Design examples. SECTION-C Unit-VI: Concrete Reinforcement and Detailing-Requirements of good detailing, cover to reinforcement, spacing of reinforcement, reinforcement splicing, Anchoring reinforcing bars in flexure and shear, curtailment of reinforcement. Unit-VII: Serviceability Limit State -Control of deflection, cracking, slenderness and vibrations, deflection and moment relationship for limiting values of span to depth, limit state of crack width, Design examples. Unit-VIII: One way and Two Ways Slabs -General considerations, Design of one way and two ways slabs for distributed and concentrated loads, Non-rectangular slabs, openings in slabs, Design Examples SECTION-D Unit-IX: Columns and Footings-Effective length, Minimum eccentricity, short columns under axial compression, Uniaxial and biaxial bending, slender columns, Isolated and wall footings, Design examples. Unit-X: Retaining Walls -Classification, Forces on retaining walls, design criteria, stability requirements, Proportioning of cantilever retaining walls, counterfort retaining walls, criteria for design of counterforts, design examples. BOOKS RECOMMENDED: 1. Design of Reinforced Concrete Structures,P.Dayaratnam,Oxford & IBH Pub.,N.Delhi. 2. Reinforced Concrete-Limit State Design, A.K.Jain, Nem Chand & Bros.,Roorkee. 3. Reinforced Concrete, I.C.Syal & A,K,Goel, A.H,Wheeler & Co.Delhi. 4. Reinforced Concrete Design, S.N.Sinha, TMH Pub.,N.Delhi. 5. SP-16(S&T)-1980, Design Aids for Reinforced Concrete to IS:456, BIS, N.Delhi. 6. SP-34(S&T)-1987 Handbook on Concrete Reinforcement and Detailing`, BIS, N.Delhi. |