01-04-2015, 04:57 PM
MECHANICS OF SOLIDS will update index soon till then download notes from notes section
UNIT-I
Compound stress and strains: Introduction, normal stress and strain, shear stress and strain, stresses on inclines sections, strain energy, impact loads and stresses, state of plane stress, principal stress and strain, maximum shear stress, Mohr’s stress circle, three dimensional state of stress & strain, equilibrium equations, generalized Hook’s law, theories of failure
UNIT –II
Stresses in Beams: Pure Bending, normal stresses in beams, shear stresses in beams due to transverse and axial loads, composite beams.
Deflection of Beams: Equation of elastic curve, cantilever and simply supported beams, Macaulay’s method, moment area method, fixed and continuous beams
Torsion: Torsion, combined bending & torsion of solid & hollow shafts, torsion of thin walled tubes
UNIT-III
Helical and Leaf Springs: Deflection of springs by energy method, helical springs under axial load and under axial twist (respectively for circular and square cross sections) axial load and twisting moment acting simultaneously both for open and closed coiled springs, laminated springs.
Columns and Struts: Buckling and stability, slenderness ratio, combined bending and direct stress, middle third and middle quarter rules, struts with different end conditions, Euler’s theory for pin ended columns, effect of end conditions on column buckling, Ranking Gordon formulae, examples of columns in mechanical equipments and machines.
UNIT-IV
Thin cylinders & spheres: Introduction, difference between thin walled and thick walled pressure vessels, Thin walled spheres and cylinders, hoop and axial stresses and strain, volumetric strain.
Thick cylinders: Radial, axial and circumferential stresses in thick cylinders subjected to internal or external pressures, compound cylinders, stresses in rotating shaft and cylinders, stresses due to interference fits.
UNIT-V
Curved Beams: Bending of beams with large initial curvature, position of neutral axis for rectangular, trapezoidal and circular cross sections, stress in crane hooks, stress in circular rings subjected to tension or compression.
Unsymmetrical Bending: Properties of beam cross-section, slope of neutral axis, stress and deflection in unsymmetrical bending, determination of shear center and flexural axis (for symmetry about both axis and about one axis) for I-section and channel section.
Books and References :
1. Mechanics of Materials by Hibbeler, Pearson.
2. Mechanics of Materials by.Beer, Jhonston, DEwolf and Mazurek, TMH
3. Strength of Materials by Pytel and Singer, Harper Collins
4. Strength of Materials by Ryder, Macmillan.
5. Strength of Materials by Timoshenko and & Yσungs, East West Press.
6. Introduction to Solid Mechanics by Shames, PHI
7. Strength of Materials by Nag and Chandra, Wiley India.
8. Strength of Materials by Nash (Sp Indian Edition), TMH
9. Strength of Materials by Jindal, Pearson Education
10. Strength of Material by Bhavikatti, Vikas Publishing.
11. Fundamentals of Solid Mechanics by Gambhir, PHI
12. Strength of Materials by Basavajaiah and Mahadevappa, University Press.
UNIT-I
Compound stress and strains: Introduction, normal stress and strain, shear stress and strain, stresses on inclines sections, strain energy, impact loads and stresses, state of plane stress, principal stress and strain, maximum shear stress, Mohr’s stress circle, three dimensional state of stress & strain, equilibrium equations, generalized Hook’s law, theories of failure
UNIT –II
Stresses in Beams: Pure Bending, normal stresses in beams, shear stresses in beams due to transverse and axial loads, composite beams.
Deflection of Beams: Equation of elastic curve, cantilever and simply supported beams, Macaulay’s method, moment area method, fixed and continuous beams
Torsion: Torsion, combined bending & torsion of solid & hollow shafts, torsion of thin walled tubes
UNIT-III
Helical and Leaf Springs: Deflection of springs by energy method, helical springs under axial load and under axial twist (respectively for circular and square cross sections) axial load and twisting moment acting simultaneously both for open and closed coiled springs, laminated springs.
Columns and Struts: Buckling and stability, slenderness ratio, combined bending and direct stress, middle third and middle quarter rules, struts with different end conditions, Euler’s theory for pin ended columns, effect of end conditions on column buckling, Ranking Gordon formulae, examples of columns in mechanical equipments and machines.
UNIT-IV
Thin cylinders & spheres: Introduction, difference between thin walled and thick walled pressure vessels, Thin walled spheres and cylinders, hoop and axial stresses and strain, volumetric strain.
Thick cylinders: Radial, axial and circumferential stresses in thick cylinders subjected to internal or external pressures, compound cylinders, stresses in rotating shaft and cylinders, stresses due to interference fits.
UNIT-V
Curved Beams: Bending of beams with large initial curvature, position of neutral axis for rectangular, trapezoidal and circular cross sections, stress in crane hooks, stress in circular rings subjected to tension or compression.
Unsymmetrical Bending: Properties of beam cross-section, slope of neutral axis, stress and deflection in unsymmetrical bending, determination of shear center and flexural axis (for symmetry about both axis and about one axis) for I-section and channel section.
Books and References :
1. Mechanics of Materials by Hibbeler, Pearson.
2. Mechanics of Materials by.Beer, Jhonston, DEwolf and Mazurek, TMH
3. Strength of Materials by Pytel and Singer, Harper Collins
4. Strength of Materials by Ryder, Macmillan.
5. Strength of Materials by Timoshenko and & Yσungs, East West Press.
6. Introduction to Solid Mechanics by Shames, PHI
7. Strength of Materials by Nag and Chandra, Wiley India.
8. Strength of Materials by Nash (Sp Indian Edition), TMH
9. Strength of Materials by Jindal, Pearson Education
10. Strength of Material by Bhavikatti, Vikas Publishing.
11. Fundamentals of Solid Mechanics by Gambhir, PHI
12. Strength of Materials by Basavajaiah and Mahadevappa, University Press.